Location of cords and cables, fault detection
TDR-420Time Domain ReflectometerTDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected. Two cursors allow to determine the place of two damages simultaneously and the distance between them. Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret. Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.NEWNEW
LKZ-2000Wires and pipe locatorEasily locate cables and pipes with pinpoint accuracy. The complexity of large underground utilities networks is continually increasing. So obtaining precise information on the location of specific buried cables and pipes has never been so important in order to protect burried assets during ground excavation work and supporting the mapping and surveying of these existing utilities. Sonel LKZ-2000 system has a unique flexible operating modes to help you easily decide the right mode for your locating application and site conditions. The intelligent utility locator monitors the signal interference levels in all available modes and recommends which to use for the best results. Saving you time and giving you increased confidence in your results. Sonel LKZ-2000 - the best system for most challenging conditions! POWER INDUSTRY Sonel LKZ-2000 is designed to easily trace power cables over long and short distances with pinpoint accuracy, especially in areas with high levels of electrical interference. When used in conjunction with the supplied Multi Clamp a trace signal can be safely applied to an electrically live cable. The A-Frame accessory can also be used to easily locate cable sheath faults. CIVIL ENGINEERING AND CONSTRUCTION INDUSTRIES The highly durable, weatherproof Sonel LKZ system has a flexible operating system to suit most site conditions and terrain, which is essential on complex and demanding civil engineering and construction sites. RAIL INDUSTRY Damaging communication cables can be very costly and time consuming to repair, causing major disruption to the rail network. Sonel LKZ system is designed to easily locate and trace cables in congested areas and with high levels of electrical interference. TELECOM INDUSTRY Tracing and locating large bundled cables, such as fibre optic cables, can be difficult and time consuming. Sonel LKZ systems high frequency modes are ideally suited for these types od cables, helping to improve your productivity and locating reliability of all cable types. The A-Frame accessory can be used to easily locate cable sheath faults. GAS & OIL INDUSTRIES These can be the most potentially hazardous, costly or environmentally sensitive pipes to strike and therefore most important not to damage. Using the Sonel LKZ system’s range of low frequency modes, locating and tracing these pipes is easy over long distances, maintaining maximum accuracy. WATER INDUSTRY Locating and tracing pipes can support the mapping and surveying of utilities. Using the Sonel LKZ system with our dual frequency sonde is the ideal solution for locating deep underground non-metallic sewerage and drainage pipes, that can’t be detected using standard locating technology.
LKZ-1500Wires and pipe locatorThe LKZ-1500 set for underground utility localization, consisting of a transmitter and receiver, allows you to locate, identify and track the route of buried objects in the ground, such as: power and control cables, data and telecommunications cables, underground lighting and cathodic protection systems, water and sewage installations, fuel and transmission installations: gas and other pipelines, heating systems and preinsulated pipes. Recipients (customers) of LKZ-1500 include energy and installation companies, earthworks, construction, railways, telecommunications, fixtures, water and sanitary installations, district heating companies and geodetic offices.
LKZ-1000Wires and pipe locatorPassive or active modes of tracing. Detection of underground live wires. Detection of underground wires with no voltage (radio mode). Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection). Tracing metallic or non-conductive pipes using an additional probe. Tracing non-conductive pipelines using a “floating” probe. Tracing a determined cable. Determining the depth of a cable.
LKZ-720Wires and pipe locatorDetection of wires and cables (live or not) detection of cables in ceilings, walls and floors, detection of breaks in cables, tracing cables in building installation, locating power points and switches in buildings, locating short circuits between leads, tracing shielded cables, tracing cables in metal ducts. Identification of fuses on the distribution board. Tracing underground cables. Tracing conductive water and heating pipelines. Non-contact detection of live cables. Features: the function 3D in the receiver - detecting the direction of current flow and accurate locating the object, phase detection mode, receiver operation with four transmitters at the same time to locate interruptions or distinguish wires, a LED bright torch, headphone socket in receiver, screens backlight for work in dark, transmission battery status and settings of the transmitter to the receiver operation in wide range of rated voltage, up to 500V RMS, measurement of voltage at the object to 500 Vrms, three levels of transmitter amplification, automatic or manual selection of transmitter operation modes, five modes of wire tracer operation - voltage, current, current-voltage, power and clamp, software upgrade via USB, additional accessories enable precise localization - such as contact or non-contact probes and measurement clamp.
TDR-410TDR – Time-domain reflectometerLocation damaged power cables. Fault location copper telecom cables. Coaxial cable fault location. Fault location wiring infrastructure. Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable. Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.